Mcb 2 Ampere Berapa Watt . ( dibagi saja kedua bilangan data diatas dengan angka ampere nya agar didapat 1 ampere = ? 2,2 ampere = 400 watt 1 ampere = ? Mcb C2 Berapa Watt? Simak Bagaimana Cara Menghitung Ampere from www.pipindo.com P 1φ = i 2 x r x cos φ = 2 2 x 122 x 0,22 = 107,36 watt jika terdapat motor listrik 3 phase yang bekerja dengan hubungan bintang 2a dan apabila tegangan phasa adalah 222 v dan cos φ = 0,22. ( dibagi saja kedua bilangan data diatas dengan angka ampere nya agar didapat 1 ampere = ? Itu artinya, alat tersebut dapat menahan daya listrik sebanyak 900 watt.
Voltage Drop In 3 Phase Cable. Vd = (200) x (0.0218 ohms) x 1.73 (multiple a factor 1.73 for 3 phase systems) vd = 7.55 volts; So, vd = 1.732 x 21.2 x 100 x 80/83,690 = 3.51 voltage drop example 3 — find the size of copper wire needed in a.
3 Phase Wire, 240 To +240 Voltage, Rs 5550 /piece from www.indiamart.com
Voltage drop in cable = current x cable resistance. Read our companion article voltage drop calculator So say the unbalanced three phase circuit had a vd of 4 volts the single phase vd would be 4 x 0.866 = 3.5v 1 single phase circuit say 2v + 3.5v = 5.5v total vd = 5.5 + 5.5 + 5.5 = 16.5v % volt drop = 16.5 ÷ 400 x 100 gives you a % vd of 4%
For Example, A 30M Run Of 6Mm2 Cable Carrying 3 Phase 32A Will Result In 1.5% Drop:
Electrical load of 80kw, distance between source and load is 200 meters, system voltage 415v three phase, power factor is 0.8, permissible voltage drop is 5%, demand factor is 1. Cable is directed buried in ground in trench at the depth of 1 meter. Voltage drop in cable = current x cable resistance.
This Methodology Is Similar To The Examples Given After Nec Table 9.
The line to line voltage drop v in volts (v) is equal to square root of 3 times the wire current i in amps (a) times one way wire length l in feet (ft) times the wire resistance per 1000 feet r in ohms (ω/kft) divided by 1000: V d = 1,73 x 855 x (0,196/4 x 0,9 + 0,99/4 x 0,4) x 200 / 1000 = 16v. Therefore, the voltage drop on this cable is:
Voltage Drop=(Voltage Drop Ampere/Meter) X Length X Current.
Measuring voltage drops across loads. If you consider 3c/4c cables, the manufacturer datasheet specifies the resistance in ohm/km (r). Once you get all the above data, the voltage drop can be calculated as follows.
Specify The Voltage In Volt, And Select The Phase Arrangement:
Cable pro web will automatically perform the voltage drop calculation with the specified current. 3 phase voltage drop calculation. This will be in mv.
Voltage Drops Occur Due To The Internal Resistance Of The Source, Passive Elements , Across Conductors, Across Contacts, And Across Connectors Are Undesirable Because Some Of The Energy Supplied Is Dissipated.
Actual voltage drop will be from 10 to 15% lower for larger conductor sizes and lower power factors. Length of the cable from the starting end to receiving end. The percent drop is vdrop / vsystem x 100.
Comments
Post a Comment